8in1 Power Meter Color Screen 2P Multi-function AC Energy Meter 170-270V/63A Voltage And Current Meter Standard Rail Mou

Description 1 SONOFF Zigbe3 0 USB Dongle is a universal Zigbe USB stick It can be used as a universal Zigbe gateway in Home Assistant or other open source platforms via ZHA or Zigbe2MQTT to locally control all your Zigbe sub devices so you don t need to invest in the Zigbe hubs for different brands all you need is a universal gateway Dongle Plus 2 The dongle plus has a wide range of supported devices such as BASICZBR3 S31 Lite zb SNZB01 SNZB02 SNZB03 SNZB04 ZBMINI S26R2ZB and various sub devices from various brands or flash router firmware to extend the network range 3 The limits of ZBDongle are 21 direct sub devices and up to 40 sub devices Default values from official firmware Supported to connect more by configurating yourself Updated version in the near future will be supported to work with maximum 200 sub devicesSpecifications Pre flashed with Z Stack 3 x 0 coordinator firmwareCan use ZHA in Home Assistant or use Zigbe2MQTTBase on TI CC2652P CP2102N20dBm output gainSMA interface external antennaAluminum housing effectively reduces signa1 interference from peripheralsOptional 1 5m USB extension cable for better signal rangePackage Included 1 x SONOFF Zigbe 3 0 USB Dongle E.

Description Brand ZOP POWERProduct Lipo BatteryVoltage 3 7VCapacity 750mAhCells 1SContinuous Discharge Rate 30CPlug JST PlugQuantity 6PCSize 9 8 25 42MMWeight 19g 1 pcColors Standard Colors Caution Note due to the difference between the measurement the battery dimension and weight may have little error Dont over charge or over discharge batteries Dont put it beside the high temperature condition Dont throw it into fire Dont throw it into water Package Included 6 ZOP POWER 3 7V 750mAH 30C 1S Lipo Battery1 Charger1 Charging Wire.

RadioMaster RP1 2 4GHz ExpressLRS ELRS Open Source High Refresh Rate Low Latency Nano Receiver Built in Wifi for Whoops RC Drones AirplaneThe RP1 and RP2 2 4GHz ELRS nano series receivers are open source receivers based on ExpressLRS The Nano receivers first developed by Jye Smith from the ExpressLRS development team feature ESP8285 MCU and SX1280 RF chip The RP1 has a UFL antenna socket for full range antenna use The RP2 has a built in ceramic antenna which is super light and small in size and ideal for racing The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built in WebUI with your PC or mobile phone Due to the low latency and high refresh rate RF module the RP1 and RP2 are ideal for FPV races or Long Range Suitable for Whoops drones and fixed wing models due to the ultra light and Nano size these receivers can fit just about anywhere Specification Brand RadiomasterItem RP1 Nano ExpressLRS 2 4ghz ReceiverType ISMAntenna 65mm 2 4ghz T AntennaMaximum receive refresh rate 500Hz F1000HzMinimum receiver refresh rate 25HzWorking voltage 5vWeight 2 2g Including antenna Dimension 13mm 11mm 3mmFirmware Version ExpressLRS v2 4 pre installedFW Target RadioMaster RP1 2 2400 RXBus interface CRSFBullet Point Improved PCB design is better for heat dissipation Upgraded rigid antenna with greater durability and performance LED on the top side of PCB Solder pads are improved and easier to solder to Pac.

Features The Hantek PP 200 200 MHz Oscilloscope Probe Kit provides a probe tip ground lead several marker rings tip locating sleeve and adjustment tool The probe is a passive low impedance attenuation probe The probe has been designed and calibrated for use on instruments having an input impedance of 1M paralleled by 20pF It may also be recalibrated for use on instruments having an input capacitance of 15 to 40pF The probe incorporates a two position 1X 10X slide switch in the compensating network and cable length of 1 2 meters Specification Temperature 15C to 70CAttenuation X1 X10Input Capacity 85pF 115pF 18 5pF 22 5pFOscilloscope Input capacity 15pF 40pFInput Resistance X1 1M2 X10 10M2 Bandwidth X1 DC 6MHz X10 DC 60MHz 100MHz 200MHzMax input Voltage X1 200V DC Peak AC X10 600V DC Peak ACProbe Body 95mmCoaxial Cable 1200mm Package includes 1 x Probe Tip1 x Ground Lead 2 x Marker Ring 1 x Tip Locating Sleeve1 x Adjustment Tool Details pictures.

Features The Hantek PP 200 200 MHz Oscilloscope Probe Kit provides a probe tip ground lead several marker rings tip locating sleeve and adjustment tool The probe is a passive low impedance attenuation probe The probe has been designed and calibrated for use on instruments having an input impedance of 1M paralleled by 20pF It may also be recalibrated for use on instruments having an input capacitance of 15 to 40pF The probe incorporates a two position 1X 10X slide switch in the compensating network and cable length of 1 2 meters Specification Temperature 15C to 70CAttenuation X1 X10Input Capacity 85pF 115pF 18 5pF 22 5pFOscilloscope Input capacity 15pF 40pFInput Resistance X1 1M2 X10 10M2 Bandwidth X1 DC 6MHz X10 DC 60MHz 100MHz 200MHzMax input Voltage X1 200V DC Peak AC X10 600V DC Peak ACProbe Body 95mmCoaxial Cable 1200mm Package includes 1 x Probe Tip1 x Ground Lead 2 x Marker Ring 1 x Tip Locating Sleeve1 x Adjustment Tool Details pictures.